油气管道维抢修密封卡具的安全检测与应用

针对油气管道维抢修所使用密封卡具在使用过程中存在安全隐患的问题,提出了1种密封卡具的安全检测方法,并设计了检测平台。检测平台主要由管段夹持装置、密封卡具组件、实验管段、液压注剂系统以及压力测量系统等构成;检测方法包括密封卡具的出厂强度检验、密封性能测试以及安全施工压力测试,通过检测来确保施工过程中密封卡具的安全稳定性及密封作业的成功率;在新疆油田采油一厂进行了现场应用,对泄漏管段进行现场勘测后设计加工了适用的密封卡具,对该卡具进行了室内安全检验,并依据注剂式密封技术的相关标准在现场实施了带压密封作业。研究结果表明:所加工密封卡具的强度、密封性能安全可靠,现场安全注剂压力不应超过22 MPa,管道未发生二次破坏,密封效果良好。     

电梯制动器机械装置提起（或释放）验证的研究

为确保电梯制动器检测开关能够准确检测电梯制动器机械装置提起（或释放）的异常,消除异常造成的危险情况,结合电梯制动器的型式和检测开关的动作原理,对各种检测开关接线方式进行分析,针对制动器的型式提出了合理的制动器检测开关接线方式。研究结果表明:直压式制动器可用1个通断状态的检测开关对其机械装置的提起（或释放）进行验证,但应在电梯的主板上设置2个检测点;杠杆式鼓式制动器应用具备2个通断状态的检测开关对其机械装置的提起（或释放）进行验证,且应采用常开并联或常闭串联的方式检测制动器机械装置的释放,采用常闭并联和常开串联的方式检测制动器机械装置的提起。     

MAGNETIC TRIGGER FOR AUTOMATIC PUMPING SAMPLERS1

ABSTRACT: A stage-activated triggering device was developed for automatic pumping samplers. The device consists of a proximity switch and ten magnets mounted radially at equal intervals on a plexiglass disk. The triggering device allows discrete sampling of stream water at 3.0 cm intervals of stage. The trigger proved dependable during two years of use at three headwater streams in the Ouachita Mountains of southeastern Oklahoma.     

城市生活垃圾中转站举升装置设计与应用

对地平式城市垃圾中转站的 3种举升装置进行了详细分析 ,指出了其存在的问题 ,提出了一种新型的链条式城市垃圾中转站举升装置 ,它结构紧凑 ,运行平稳可靠 ,成本低 ,噪音小 ,节能省电 ,是垃圾中转站新型优选产品 ,现已成功应用于环卫工程中     

烟气脱硫石灰石活性测试装置设计研究

石灰石的活性对烟气脱硫工艺具有重要意义.设计了一套石灰石活性测试装置,该装置可模拟实际脱硫塔的反应过程,测试结果能够准确反映石灰石的活性.     

温度循环下塑封器件可靠性评估分析

目的评估塑封器件的热疲劳寿命和可靠性。方法分析NASA和ECSS空间任务用低等级器件评估标准,针对某型号任务用的两种塑封器件制定了温度循环评估方案。在-55~+125℃进行500次温度循环,配合外观检查、X射线检查、声学扫描显微镜检查、常温测试检测项目。结果 SOP-8(Small Out-line Package)器件评估合格,各项检测试验项目合格,其可靠性寿命满足某型号任务单机载荷2年需求。SOT-23(Small Out-line Transistor Package)器件出现功能失效,分层扩展至整个焊板区域,内部键合丝断裂,电参数失效比例为95%。结论塑封器件评估需要制定有针对性的评估方案,经评估验证,部分塑封器件的可靠性可满足高可靠领域任务需求,兼备高可靠性与高性能。     

Effect of posture on forces and moments measured in a Hybrid III ATD lower leg

Objective: Anthropomorphic test devices (ATDs) are used to assess real injury risk to occupants of vehicles during injurious events. In the lower leg, values from load cells are compared to injury criteria developed in cadaveric studies. These criteria are typically developed with the leg in a neutral posture, whereas the ATD may assume a wide range of postures during safety evaluation tests. The degree to which the initial posture of an ATD has an effect on the measured forces and moments in the lower leg is unknown.

Methods: A Hybrid III ATD lower leg was impacted in a range of postures under conditions representing a crash test, and peak axial force and adjusted tibia index injury measures were evaluated. Ankle posture was varied in 5° increments using a custom-made footplate, and dorsi/plantarflexion (20° DF to 20° PF) and in/eversion (20° IV to 5° EV) were evaluated. Tibia angle was also varied (representing knee flexion/extension) by ±10° from neutral.

Results: Peak axial force was not affected by ankle flexion or tibia angulation. Adjusted tibia index was lowest for plantarflexion, as well as for tibia angles representative of knee extension. Both peak axial force and adjusted tibia index were lowest for postures of great inversion and were highest in neutral or near-neutral postures.

Conclusions: The range of postures tested herein spanned published injury criteria and thus would have made the difference between pass and fail in a safety evaluation. In/eversion had the largest influence on injury metrics, likely due to the change in axial stiffness and altered impact durations in these postures. Results suggest increased injury risk at neutral or near-neutral postures, whereas previous cadaveric studies have suggested that in/eversion does not influence injury risk. It is unclear whether the ATD appropriately represents the natural lower leg for impacts in out-of-position testing. Great care must be taken when initially positioning ATDs for safety evaluations, because small perturbations in posture were shown herein to have large effects on the measured injury risk using this tool.     

Comparison of current ATDs with Chinese adults in anthropometry

Objective: Crash test dummies are full-scale anthropomorphic test devices (ATDs) that simulate the dimensions, weight proportions, and articulation of the human body and are used to measure human injury potential in vehicle crashes. The Hybrid III dummy family, which is widely used currently, takes selected percentiles of anthropometry dimensions of U.S. adults as design references. The objective of this study was to assess the difference in anthropometry between Chinese adults and the currently used dummy.

Methods: Based on the Chinese National Physical Fitness Surveillance of the year 2000, 2005, 2010 and National Standard of China GB/T 10000–1988, a series of anthropometric parameters for Chinese adults were obtained, and data analysis was conducted between Chinese adults and ATDs that are currently used.

Results: The comparison revealed distinct anthropometric difference between ATDs and Chinese adults. Based on the latest data, median Chinese females were about 2.6% lower in stature and about 8.03% lower in body weight than the ATD design targets. Similarly, median Chinese males were about 3.48% shorter and weighed 11.89% less than the ATD design targets.

Conclusions: Although the anthropometric differences between Chinese adults and the Hybrid III ATD specifications were modest and growing smaller, it is advisable to take the differences in anthropometry between ATDs and Chinese adults into consideration when developing new vehicles in China to provide effective protection specifically for Chinese occupants.     

基于SAE-ARP958环天线校准技术研究

目的介绍基于SAE-ARP958环天线校准技术,研究提高该校准精确性的方法,为精确监测电磁环境提供保障。方法研制一套基于SAE-ARP958环天线的校准装置,提出采用直径分别为30,10,4 cm的三个发射环天线作为磁场发生装置的校准方案,并利用对比测试的方法对校准方案进行优化。结果优化后的校准方案能够实现环天线的精确校准。结论基于SAE-ARP958环天线校准方法具有不受待校环尺寸限制的优点,而且精确性高,值得向具有较多不同尺寸的环天线用户推广。